Sonix MCU  (45)
Elan MCU  (51)
RF芯片  (12)
HD EEPROM  (1)
Metal link  (1)
优势M0  (3)
HD FLASH  (14)
直流马达  (2)
优势FLASH  (12)
EM78F668N

EM78F668N is an 8-bit microprocessor designed and developed with low-power, high-speed CMOS technology. It is
equipped with 8K*15-bits Electrical Flash Memory, 256*8 bits in system programmable EEPROM, two comparators, three
8 bits timers, one 16 bits timer, two 10 bits PWM, 8 channels AD with 12 bits resolution, SPI, UART and I2C.
With its Flash-ROM feature, the EN78F668N is able to offer a convenient way of developing and verifying users'
programs. Moreover, users can take advantage of EMC Writer to easily program his development code.

  • CPU configuration
  • Support 8K×15 bits program ROM
  • 304×8 bits on chip registers (SRAM)
  • 256 bytes in-system programmable EEPROM

                    *Endurance: 1,000,000 write/erase cycles

  • More than 10 years data retention
  • 8 level stacks for subroutine nesting
  • Less than 2 mA at 5V/4MHz
  • Typically 20 μA, at 3V/32kHz
  • Typically 2 μA, during sleep mode
  • Four operation mode
Mode 
 
CPU Main

clock

WDT

clock

Sleep mode Turn off Turn off Turn off
Idle Mode Turn off Turn off Turn on
Green mode Turn on Turn off Turn on
Normal mode Turn on Turn on Turn on
  • I/O port configuration
  • 5 bidirectional I/O ports: P5, P6, P7, P8, P9
  • Pin change wake-up port : P6
  • 40 programmable pull-down I/O pins
  • 40 programmable pull-high I/O pins
  • 40 programmable open-drain I/O pins
  • 40 programmable high-sink/drive I/O pins
  • External interrupt : P60
  • Operating voltage range:
  • 2.4V~5.5V at 0°C~70°C (commercial)
  • 2.6V~5.5V at -40°C~85°C (industrial)
  • Operating frequency range (base on 2 clocks):
  • Crystal mode:

DC ~ 20MHz at 5V

DC ~ 8MHz at 3V

DC ~ 4MHz at 2.4V

  • ERC mode:

DC ~ 20MHz at 5V

DC ~ 8MHz at 3V

DC ~ 4MHz at 2.4V

  • IRC mode

DC ~ 16MHz at 4.5V~5.5V

DC ~ 8MHz at 3V

DC ~ 4MHz at 2.4V~5.5V

  • Internal RC Drift Rate (Ta=25°C, VDD=5V±5%,VSS=0V)
Internal RC

Frequency

Drift Rate
Temperature

(-40°C+85°C)

Voltage

(2.2V~5.5V)

Process Total
455kHz ±5% ±5% ±4% ±14%
4MHz ±5% ±5% ±4% ±14%
8MHz ±5% ±5% ±4% ±14%
16MHz ±5% ±5% ±4% ±14%
  • Peripheral configuration
  • 8-bit real time clock/counter (TCC) with selective signal sources, trigger edges, and overflow interrup
  • Two Pulse Width Modulation (PWMA,B) with 10-bit resolution which shared with Timer A,B
  • Two 8 bits Timer/Counter: TC1: Timer/Counter/Capture mode selection

TC3: Timer/Counter/PWM/PDO(programmabledivider output)

Mode selection

  • One 16 bits Timer/Counter:

TC2: Timer/Counter/Window mode selection

  • 4 programmable Level Voltage Detector (LVD): Vdd power monitor and support low voltage detector  interrupt flag
  • 8 channels Analog-to-Digital Converter with 12-bitresolution in Vref mode
  • One pair of comparator
  • Serial transmitter/receiver interface (SPI): three wiresynchronous communication
  • Universal asynchronous receiver transmitterinterface (UART): two wire asynchronous communication
  • Power-down (Sleep) mode
  • High EFT immunity(4MHZ,4clocks)
  • I2C function with 7/10 bits address & 8 bits data transmit/receive mode
  • 18 available interrupts(4 external, 14 internal )
  • External interrupt(P60)
  • TCC overflow interrupt
  • TC1,TC2, TC3 overflow interrupt
  • Input-port status changed interrupt (wake up from sleep mode)
  • ADC completion interrupt
  • PWMA, PWMB period match completion
  • Comparator high/low interrupt
  • I2C transfer/receive/stop interrupt
  • UART TX, RX , RX error interrupt
  • SPI interrupt
  • LVD interrupt
  • Programmable free running Watchdog Timer
  • Watchdog Timer: 16.5ms ± 5% with Vdd =5V at25°C, Temperature range ± 5% (-40°C ~+85°C)
  • Watchdog Timer: 18ms ± 5% with Vdd = 3V at 25°C Temperature range ± 5% (-40°C~+85°C)
  • Two clocks per instruction cycle
  • Package Type:
  • 44 pin QFP: EM78F668NQ44J/S
  • 40 pin DIP: EM78F668ND40J/S
  • 28 pin SKDIP: EM78F668NK28J/S
  • 28 pin SOP: EM78F668NSO28J/S

Note: Green products do not contain hazardous substances.

  • 99.9% single instruction cycle commands
  • There are 4 kinds of oscillation ranges in crystal mode
Crystal ranges Oscillator Mode
20MHz~6MHz HXT
6MHz~1MHz XT
1MHz~100KHz LXT1
32.768KHz LXT2

上海俊硕电子科技有限公司 版权所有 © 严禁复制  2000-2014
电话:18101791225 传真:021-36360067 技术支持:上海频道
地址:上海市共和新路3737号共和国际商务广场B楼1709室   网站备案号:沪ICP备16018318号-1